ANMYZ

English
  • English
  • Portugal
  • Español
  • عربي
  • Türk
  • Русский
  • فارسی

ANMYZ

English
  • English
  • Portugal
  • Español
  • عربي
  • Türk
  • Русский
  • فارسی

AZ-1682 – Stone adhesive/Epoxy resin system for mesh reinforcement on the back of marble and granite slabs

Stone adhesive/Epoxy resin for reinforcing marble/granite slabs with fiberglass mesh (applied to the back/underside)
Application:
Primarily used for reinforcing the back (underside) of various types of stone (marble, limestone, granite, sandstone) using fiberglass mesh. Can serve as a replacement for the following products:
RESIN 5008 with BB25.
Nebrax 121 with catalyst.

Price Interview

Price Interview

AZ-1682 – Stone adhesive/Epoxy resin system for mesh reinforcement on the back of marble and granite slabs

Interview

Select the number of specifications

Please check the product information you want!

Product Detail Applications & Benefits

Mixing ratio: A:B = 4:1

Color: Colorless, transparent liquid.

Viscosity (25°C, mPa•s):

A: 800–1200

B: 300–500

Gel time (25°C, min): 15–25

Curing time (25°C, h): 3–4

Tensile shear strength (MPa): ≥8

Can be used for coating marble surfaces, repairing cracks and holes, and enhancing surface gloss after polishing.

250 kg/set

[Product Advantages]

1. High adhesion and strength; excellent penetration into small cracks;

2. Low odor; poses no health risks to workers;

3. Good resistance to aging and yellowing;

4. Compliant with GB18583 and RoHS standards; environmentally friendly.

[Instructions]

1. Surface Preparation

The stone slabs must be completely dry.

Remove any mud, oil, or other impurities from the surface of the slab.

2. Preparation and Mixing

Mix the adhesive at a ratio of A:B = 4:1 (by weight) until a homogeneous mixture is obtained.

Use the adhesive within its pot life. The adhesive generates heat during the reaction; do not use it once the pot life has expired. A larger volume of mixed adhesive or a higher temperature will result in a shorter pot life. If preparing a large quantity, divide it promptly for use.

Do not swap the lids for components A and B. Keep the containers tightly closed at all times to prevent the entry of moisture or dust from the air. It is recommended to use wide-mouthed containers for mixing to extend the pot life (usable life) of the adhesive.

3. Adhesive Application

Spread the adhesive evenly over the surface of the slab using an applicator with a back-and-forth motion. The recommended application rate is 80–150 g/m².

For cracks in the slabs, apply the adhesive using a back-and-forth motion to ensure complete penetration.

For larger defects in the slab (such as embedded soil or debris), first remove the foreign material; then, mix the adhesive with stone dust to perform the repair. Once cured, polish the area and reapply the adhesive. Do not use surface treatment agents that are not epoxy-based, as they may render the surface unsuitable for the application of epoxy adhesive.

4. Curing

The adhesive will undergo initial curing within 2 to 3 hours at room temperature (25 °C); the next processing stage can begin after 24 hours.

If possible, heat the stone (with the adhesive applied) to a temperature between 50 °C and 60 °C, and proceed with polishing after 2 to 3 hours.

Before the adhesive has cured, the stone must be kept in a horizontal position and not stacked. Once cured, a release agent—such as talcum powder—may be applied to the stone surface to prevent the slabs from sticking together when stacked.

5. Cleaning

Use an appropriate cleaning agent to sanitize equipment before the adhesive cures.


AZ-1682 Epoxy Resin for Back Netting

AZ-1682 Epoxy Resin for Back Netting is a two-component epoxy adhesive system formulated for reinforcing the back of marble, granite, limestone and sandstone slabs with fiberglass mesh. Supplied as components A and B, it cures to a strong, durable bond within the stone and is designed for the demands of natural stone processing and repair. A controlled mixing ratio of A:B = 4:1 gives repeatable results, and the cured resin delivers tensile shear strength of >=8 MPa.

Technical data: viscosity at 25 C is A 800-1200 / B 300-500 mPa.s. Gel time at 25 C is 15-25 min, with a curing time of 3-4 h. The low-viscosity formulation penetrates fine cracks and porous stone before hardening, which is essential for deep, uniform reinforcement. The cured resin is colorless and transparent where clarity matters for the finished stone appearance.

How it is applied: components A and B are mixed in the specified ratio, then poured or injected into the prepared crack, fissure or reinforcement zone. For vacuum infusion, the resin is drawn through flow media into the stone under vacuum. For surface repair, it is applied to fissures and allowed to cure before polishing. Correct mixing and pot life management are important for a complete cure.

Applications: reinforcing the back of marble, granite, limestone and sandstone slabs with fiberglass mesh. The product is compatible with ANMYZ fiberglass mesh, vacuum bagging consumables and dispensing equipment for a complete working system.

Why choose ANMYZ: our epoxy resin range covers block coating, back netting, crack repair and luxury stone restoration, and our technical team can recommend the right formulation for your stone and process. Contact us for data sheets, packing sizes and pricing.

No comment

Product Detail

Mixing ratio: A:B = 4:1

Color: Colorless, transparent liquid.

Viscosity (25°C, mPa•s):

A: 800–1200

B: 300–500

Gel time (25°C, min): 15–25

Curing time (25°C, h): 3–4

Tensile shear strength (MPa): ≥8

Can be used for coating marble surfaces, repairing cracks and holes, and enhancing surface gloss after polishing.

250 kg/set

[Product Advantages]

1. High adhesion and strength; excellent penetration into small cracks;

2. Low odor; poses no health risks to workers;

3. Good resistance to aging and yellowing;

4. Compliant with GB18583 and RoHS standards; environmentally friendly.

[Instructions]

1. Surface Preparation

The stone slabs must be completely dry.

Remove any mud, oil, or other impurities from the surface of the slab.

2. Preparation and Mixing

Mix the adhesive at a ratio of A:B = 4:1 (by weight) until a homogeneous mixture is obtained.

Use the adhesive within its pot life. The adhesive generates heat during the reaction; do not use it once the pot life has expired. A larger volume of mixed adhesive or a higher temperature will result in a shorter pot life. If preparing a large quantity, divide it promptly for use.

Do not swap the lids for components A and B. Keep the containers tightly closed at all times to prevent the entry of moisture or dust from the air. It is recommended to use wide-mouthed containers for mixing to extend the pot life (usable life) of the adhesive.

3. Adhesive Application

Spread the adhesive evenly over the surface of the slab using an applicator with a back-and-forth motion. The recommended application rate is 80–150 g/m².

For cracks in the slabs, apply the adhesive using a back-and-forth motion to ensure complete penetration.

For larger defects in the slab (such as embedded soil or debris), first remove the foreign material; then, mix the adhesive with stone dust to perform the repair. Once cured, polish the area and reapply the adhesive. Do not use surface treatment agents that are not epoxy-based, as they may render the surface unsuitable for the application of epoxy adhesive.

4. Curing

The adhesive will undergo initial curing within 2 to 3 hours at room temperature (25 °C); the next processing stage can begin after 24 hours.

If possible, heat the stone (with the adhesive applied) to a temperature between 50 °C and 60 °C, and proceed with polishing after 2 to 3 hours.

Before the adhesive has cured, the stone must be kept in a horizontal position and not stacked. Once cured, a release agent—such as talcum powder—may be applied to the stone surface to prevent the slabs from sticking together when stacked.

5. Cleaning

Use an appropriate cleaning agent to sanitize equipment before the adhesive cures.


Applications & Benefits

AZ-1682 Epoxy Resin for Back Netting

AZ-1682 Epoxy Resin for Back Netting is a two-component epoxy adhesive system formulated for reinforcing the back of marble, granite, limestone and sandstone slabs with fiberglass mesh. Supplied as components A and B, it cures to a strong, durable bond within the stone and is designed for the demands of natural stone processing and repair. A controlled mixing ratio of A:B = 4:1 gives repeatable results, and the cured resin delivers tensile shear strength of >=8 MPa.

Technical data: viscosity at 25 C is A 800-1200 / B 300-500 mPa.s. Gel time at 25 C is 15-25 min, with a curing time of 3-4 h. The low-viscosity formulation penetrates fine cracks and porous stone before hardening, which is essential for deep, uniform reinforcement. The cured resin is colorless and transparent where clarity matters for the finished stone appearance.

How it is applied: components A and B are mixed in the specified ratio, then poured or injected into the prepared crack, fissure or reinforcement zone. For vacuum infusion, the resin is drawn through flow media into the stone under vacuum. For surface repair, it is applied to fissures and allowed to cure before polishing. Correct mixing and pot life management are important for a complete cure.

Applications: reinforcing the back of marble, granite, limestone and sandstone slabs with fiberglass mesh. The product is compatible with ANMYZ fiberglass mesh, vacuum bagging consumables and dispensing equipment for a complete working system.

Why choose ANMYZ: our epoxy resin range covers block coating, back netting, crack repair and luxury stone restoration, and our technical team can recommend the right formulation for your stone and process. Contact us for data sheets, packing sizes and pricing.

AZ-1682 – Stone adhesive/Epoxy resin system for mesh reinforcement on the back of marble and granite slabs
Stone adhesive/Epoxy resin for reinforcing marble/granite slabs with fiberglass mesh (applied to the back/underside)
Application:
Primarily used for reinforcing the back (underside) of various types of stone (marble, limestone, granite, sandstone) using fiberglass mesh. Can serve as a replacement for the following products:
RESIN 5008 with BB25.
Nebrax 121 with catalyst.
Long press to look detail
Long by picture save/share
INQUIRY

enquiry form:

  • Please enter the verification code

Inquiry Content:


You have no items to require

Add Successfully

AZ-1682 – Stone adhesive/Epoxy resin system for mesh reinforcement on the back of marble and granite slabs

enquiry
INQUIRY

enquiry form:

  • Please enter the verification code

Inquiry Content:


You have no items to require

Add Successfully

PRODUCTS

Epoxy Resin system for stones

Fiberglass mesh/woven

Abrasive

Diamond tools

 

 CONTACT

 

Tel: +852-59278153 
Tax:+852-59278153

Email : [email protected]

COMPANY

About   |  Production Ability    |   Our Advantages   |   Trade Capacity

 

PRODUCTS

Stone adhesive   |   Fiberglass mesh/woven

Abrasive   |   Vaccum Perfusion System

Copyright © 2015-2035 Anmyz Industry Ltd. All Rights Reserved. 

Phone
+86-15920009441
Working Time
Monday to Friday
Qrcode
Whatsapp
Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.